OMTech 60W 28x20inch CO2 laser Cutter Engraver Ruida with CW-5200 Water Chiller. OMTech 60W CO2 Laser Engraver.Combining ease of use with advanced capability, this intuitive 60W CO2 laser engraver delivers professional results at a fraction of the cost. Equipped with a powerful 60-watt water-cooled laser tube, high-precision stepper motor, and a top-quality Ruida LCD control board, it features our largest engraving surface (28" x 20") with a height-adjusting lift table and dual pass-through doors to accommodate oversized and irregular-shaped objects, making it one of our most highly capable engraving machines. Simply plug in the USB connector to your computer system and you're ready to start your laser engraving story! To go along with your laser machine!
The intuitive control panel with a digital display allows complete control of the laser head, pausing and stopping projects, adjusting laser power and speed settings, file viewing, and project framing via Windows-compatible RDWorks v8. Two-way pass allows you to feed material into the workbed from the front or back and cut materials larger than your bed size by sliding them through the cabinet. Laser tube provides 60W of power for up to 2000 hours or lasts twice as long when consistently used at lower settings. One USB port reads flash drives while the other connects directly to your PC via dedicated cable. The Ethernet port allows you to work remotely online.Equipped with X and Y stepper motors for efficient power transmission between the guide rails with high precision and long service life. A red dot pointer mounted on the laser head quickly indicates engraving points, marks the machine's path, and identifies positioning sizes, allowing an effortless project setup process. The laser nozzle can extend downwards up to 1.75 or be fully retracted, allowing more control over different focal distance setups. A pre-installed air compressor guides a pressurized air stream through the laser head nozzle to displace debris, heat, and combustible gases from the engraving surface and laser beam path, keeping your workbed cleaner and engravings more precise. (500×700 mm) workbed gives you plenty of space to work on wood, rubber, plastic, paper, fabric, leather, ceramics, tile, fiberglass, marble, stone, and more-even before you open the integrated pass-through doors that permit you to work on even larger pieces! Pre-installed hoses along with the included water pump allow for a fast and easy setup. Only use with distilled water, ensuring it stays between 60-70°F (16-21°C).
A pressure flow sensor monitors water flow throughout the laser engraving process and prevents the laser from firing if water stops circulating through the laser tube. A crystal-clear LCD display provides real-time information about the device's electric current and autocorrects faults, reducing damage to your laser tube and power supply in the rare case of improper ammeter connections. The transparent acrylic window's sepia filter allows you to observe your engraver in action, as the tint blocks the laser beam and protects your eyes. The laser automatically stops engraving, cutting, or marking when the workbed's cover is opened for your safety. Close the cover and press Start to resume your work.The E-Stop safety button immediately stops the machine in case of emergency. The industrial-grade laser head delivers a stable laser beam over the long service life of the machine, while the red-dot locator helps to quickly indicate engraving points and marks the engraving path, allowing effortless setup and operation. Engraving Depth: 0.25 in. Workbed Height Range: 9 in. Front/Back Pass Size 32.87×3.94 in.
Engraving Speed: 23.6 ips (600 mm/s). Cutting Speed: 15.7 ips (400 mm/s). Included Software: RDWorks 8, CorelLaser.
Graphic Operating Modes: Optimized Raster, Vector, and Combined. Transfer Interface: Flash Drive, USB Cord, Ethernet Cord.
Machine Dimensions: 47.2×34.3×36.6 in. Laser Wavelength: 10.6 µm. Laser Tube Diameter: 2 in. Laser Tube Length: 39.4 in.
Focal Lens Diameter: 18 mm. 1 x Laser Engraver Machine. 1 x Ethernet to Ethernet Cable. 1 x Venting Exhaust Duct 4 ft. 1 x USB Type-A to Type-A Cable.
1 x USB Drive with Software. 1 x Stainless Steel Clamp. 60W CO2 laser tube with an estimated lifetime of up to 2,000 operation hours depending on power setting usage and water cooling performance. PLEASE NOTE: Frequent use of high laser power settings will shorten the laser tube lifetime as follows.
Low Power 10-40% = 1,700-2,000 Hours. Moderate Power 40-70% = 1,300-1,500 Hours. High Power 70-100% = 800-1,000 Hours. Laser Cutting: Acrylic Wood Leather Plastics Fabrics MDF Cardboard Paper Corian Foam Fiberglass Rubber.
Marking/Engraving: Acrylic Wood Leather Plastics Fabrics Glass Rubber Cork Brick Granite Marble Tile River Rock Bone Melamine Phenolic Aluminum Stainless Steel Titanium. Cannot cut hardwoods like mahogany. CO2 lasers only mark bare metals when anodized or treated. Some PVC-based acrylics can create toxic fumes when lasered.Master, AmericanExpress, Discover, Google Pay. If you must modify your. Laser tube and power supply. Special circumstances will be stated clearly in the listing. If your item has been damaged in transit or. Please check everything carefully after you receive the parcel, as any. Damages except DOA (Dead-On-Arrival) are not covered if it's the fault of the consumer. Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. Parts must be resaleable and in the original packaging. We cannot take back used products. We cannot take back installed or tired products. We do reserve the right to refuse and return any parts we find have been installed, are used or do not meet the above criteria. Return request need to be within 30 days of receipt. Feedback as much as you do. If for some reason there is. As an emerging leader in manufacturing and exporting, we specialize in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for over 10 years.
It is our mission to provide innovative products and competitive prices to satisfy you. This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Engraving". The seller is "premiumautopart" and is located in this country: US.
This item can be shipped to United States.